1. No Water Flow or Low Water Pressure:
- Check the Water Supply: Ensure that the main water supply is turned on and the water supply valve to the purifier is fully open.
- Inspect the Inlet Valve and Tubing: Look for kinks or blockages in the inlet tubing. Clear any blockages and ensure the tubing is not pinched.
- Examine the Booster Pump: If the purifier has a booster pump, check if it is functioning properly. If the pump is not running, ensure it is connected to power and try resetting the unit.
- Replace Filters: Clogged filters can reduce water flow. If you haven’t changed the filters recently, consider replacing them as per the recommended schedule.
2. Water Tastes or Smells Unusual:
- Flush the System: After installation or filter replacement, flush the system by running water through it for 10-15 minutes. This can help remove any residual materials from the filters.
- Check the Filter Lifespan: Old or expired filters can affect the taste and quality of the water. Replace any filters that are past their lifespan.
- Sanitize the Unit: Bacteria buildup can cause unpleasant tastes or odors. Sanitize the storage tank and replace the RO membrane if necessary.
3. Leakage from the Unit:
- Inspect Connections: Check all tubing and connectors for tightness. Use Teflon tape to seal any loose or leaking connections.
- Examine the Tank: Look for cracks or damage in the storage tank. If the tank is damaged, it may need to be replaced.
- Check for Drips at the Faucet: Ensure the faucet connections are secure and the O-ring is properly seated. Tighten any loose screws or nuts.
4. Purifier Not Turning On:
- Check Power Supply: Ensure the SMPS adapter is properly plugged in and the power outlet is functioning. Try plugging the adapter into a different outlet.
- Inspect the Adapter: Look for any signs of damage to the power adapter or cord. If damaged, replace the adapter with a compatible one.
- Reset the Unit: Some models have a reset button or switch. Try resetting the purifier by turning it off and then on again after a few seconds.
5. Excessive Noise from the Purifier:
- Inspect the Pump: A booster pump may produce noise, especially if it is malfunctioning. Ensure it is securely mounted and check for any obstructions.
- Check for Air Traps: Air bubbles in the system can cause unusual sounds. Run the purifier to allow any trapped air to escape.
- Examine the Filters: Incorrectly installed or clogged filters can create noise. Make sure filters are properly seated and replace them if they appear clogged.
6. TDS Levels Are Higher Than Expected:
- Check the TDS Controller: If your purifier has a TDS controller, adjust it according to your preferred TDS levels. Refer to the user manual for instructions on adjusting the controller.
- Replace the RO Membrane: A worn-out RO membrane can result in higher TDS levels. If the membrane has not been replaced in a while, consider replacing it.
- Flush the Membrane: Some systems allow you to flush the RO membrane, which can help remove buildup and improve TDS performance.
7. Indicator Lights Not Working:
- Inspect the Power Connection: Ensure the purifier is plugged in and receiving power. A faulty adapter can cause indicator lights to malfunction.
- Replace Burned-out LEDs: If specific LED lights are not working, they may need replacement. Consult the user manual for guidance on replacing LEDs, or contact customer support.
- Check for Electrical Issues: Internal electrical faults may require professional repair. Avoid opening the unit yourself if you suspect internal electrical issues.
8. Slow Water Filtration Process:
- Replace Filters: Slow filtration can result from clogged filters. Follow the recommended filter replacement schedule to maintain optimal flow rate.
- Check Water Pressure: Low inlet water pressure can slow down the purification process. Ensure adequate water pressure at the source, or consider installing a booster pump if not already present.
- Clean the Pre-filter: If your system has a sediment pre-filter, clean or replace it as necessary, as sediment buildup can reduce flow rate.
If these tips don’t resolve your issue, consult the user manual specific to your model, or contact Aqua Create’s customer support for further assistance. Regular maintenance and timely filter replacements can help prevent many common issues and keep your purifier running efficiently.